CLASS H SERI H900 BY APEXAUDIO (lanjutan...)

[putra gumulung]

maaf numpang tanya, kalow amp h900 mampu ga 'ya buat dorong speaker acr 18700 X4 - 4ohm...

[aby_babnic]

maaf numpang tanya, kalow amp h900 mampu ga 'ya buat dorong speaker acr 18700 X4 - 4ohm...

Kasihan di cuekin,saya bantu panggil master2 sf dulu...mas @mustofa ,mas @hanz ,mas @jackariadi ,mas @roiz ,monggo di kupas...

[Rizqi]

kira2 bisa gak yah?.. =D

[roiz]

maaf numpang tanya, kalow amp h900 mampu ga 'ya buat dorong speaker acr 18700 X4 - 4ohm...

Insyallah kuat kang asal suplay n final serta pendinginan memadai. Brarti per chanel 2 speaker ya. Nek pengen tau hasilnya c0ba dulu aja. Nanti terus di review di sini.

---

Kasihan di cuekin,saya bantu panggil master2 sf dulu...mas @mustofa ,mas @hanz ,mas @jackariadi ,mas @roiz ,monggo di kupas...

Wah kang @aby_babnic ini ada ada saja. . . . Saya masih newbie banget lh0w kang

[mustofa]

kang @Rizqi kira2 ya begitu deh :-D
@putra langsung tancap aja kang...
Kalo setelah praktek suaranya gak sesuai yg diminta, nanti kitnya lempar kesaya saja =)) =))

[bruce]

maaf numpang tanya, kalow amp h900 mampu ga 'ya buat dorong speaker acr 18700 X4 - 4ohm...

mampu kang...tapi untuk maksimal pakai yang tef.....

[daud elektro]

sekian byak hlman yg saya baca2 rncna mw coba ma apex kira2 clo mw pesan ma sapa y

[raveizal]

maaf numpang tanya, kalow amp h900 mampu ga 'ya buat dorong speaker acr 18700 X4 - 4ohm...

INi postingan yang desain APEX..MR.Mile Slavkovic di www.diyaudio.com:
1. "I used TL072 on some PCB, at the end this is PA amplifier, work with 18inch subwoofer".

2. Full power of this amplifier is not 900W. Power with THD 0,5% is 1200W on 4R load, and 1800W on 2R load. Output transistor must be MJL4281A/MJL4302A for maximum power. For step mosfet use IRF2807. MJL21193/MJL21194 can be used for full power on 4R load.
Transformer minimum 1500VA for one channel 4X40V AC + 2X20V for protection circuit. 2X35A bridge and 8X10000uF/63V for PSU... are you still interesting to build this amplifier?

Silakan rakit dengan komponen, TR final dan PSU yang disarankan oleh perancangnya...pasti maknyuss utk 18"

[nafiri]

INi postingan yang desain APEX..MR.Mile Slavkovic di www.diyaudio.com:
1. "I used TL072 on some PCB, at the end this is PA amplifier, work with 18inch subwoofer".

2. Full power of this amplifier is not 900W. Power with THD 0,5% is 1200W on 4R load, and 1800W on 2R load. Output transistor must be MJL4281A/MJL4302A for maximum power. For step mosfet use IRF2807. MJL21193/MJL21194 can be used for full power on 4R load.
Transformer minimum 1500VA for one channel 4X40V AC + 2X20V for protection circuit. 2X35A bridge and 8X10000uF/63V for PSU... are you still interesting to build this amplifier?

Silakan rakit dengan komponen, TR final dan PSU yang disarankan oleh perancangnya...pasti maknyuss utk 18"

kalau yg ini hitungannya tidak usah ditanyakan lagi.... tidak pakai trik-trik an :-D

[Abel jasum]

Para momod di sf..mau tanya apa sih bedanya ZY15V Dan ZF15V (di steper h900)